HOW TO SPRAY INORGANIC ZINC PRIMERS WITH YOUR ArmorThane SPRAY SYSTEM

 



MATERIAL HANDLING IS KEY


It's more about how you handle the substance than what pump you utilize. 


Mixed primers weigh 20-30 lb/gal. Artificial zinc is powdered zinc metal mixed into a base fluid with no organic resins to keep it in suspension. This is done because the intention is to apply the zinc to lay down, touching all the other zinc and the substrate metal.


The great corrosion protection is achieved only if the sacrificial zinc is conductive to the metal substrate. 


Epoxy or polymer binders significantly decrease that conductivity from happening. That's the difference between the inorganic and the organic zinc coatings.

From a fluid handling standpoint, the material must be fully conditioned into suspension, and then kept in suspension throughout the time it is in the pail, pump, hose, and gun. If it is allowed to settle, or get strained across a ball and seat, it won't matter what equipment you are using; you will have problems. 

GETTING STARTED / SETUP

  1. Don't mix the zinc in until you are ready to spray
  2. Stand ready to spray the entire batch without stopping
  3. Bypass having the gun too much below or above the pail, as gravity will settle the zinc in the hose
  4. Use a 3/8" ID hose x 50' max length and a short whip
  5. Evade sharp elbows on siphon or outlet fluid lines
  6. Use a 30-60 mesh max filtration on pump or gun

MIXING THE FLUID AND ZINC

  1. Use a strong mixer - at least 3/4 HP drive with a 5" Jiffy-type mixer
  2. Slowly add the particles and continue mixing for 5 minutes after the powder is in
  3. Sift the mixed fluid through a 30 mesh screen
  4. Mix it for added 5 minutes
  5. Keep the combined fluid under agitation until you are done spraying and ready to flush

START SPRAYING

  1. Start with the spray gun off of the hose
  2. Load and flow fluid through the hose and back to the supply pail at low pressure
  3. Attach the gun and add enough pressure for a pattern
  4. Spray

WHEN YOU STOP SPRAYING

If you have to stop spraying, relieve the pump, hose, and gun's fluid pressure. When a pump ball is holding pressure across the seat, zinc particles will be trapped between the ball and seat. The difference in fluid pressure across the ball and seat will strain the solvent out, collecting many zinc particles at that point. 


This causes two failures:

1. Packed out particles plug the passage and restrain ball movement.

2. Some particles keep the ball from fully seating ending in high velocity "wire draw" failure of the ball and/or seat.


This applies to any valves in the system, pump checks, any ball valves, and the spray gun. Even for short stoppages, relieving fluid pressure and/or low pressure circulating, goes a long way toward keeping things working well. Flush as soon as you are done spraying.


FLUSHING

Flushing tends to wash the zinc out of suspension even more. Don't let it sit in the pump. Flush at a fairly high velocity to clean out the dead areas. Remember, velocity cleans, not pressure.

  1. Circulate the flush back into the pail with the agitator off, and the siphon pick-up tube up off the bottom
  2. Finally, dismantle and clean the lower to get any packed zinc off of the checks and packings



PUMP LOWERS

ArmorThane LOWERS VS. THE COMPETITION

ArmorThane Machinery lowers the best to use for these materials, mainly because they are easier to knock down and clean or service than the competitors' pumps. None of our competitors offer pump lowers with better balls, seats, or rod and cylinder coatings than ArmorThane Machinery offers, but some of those models are much harder to service.


If the balls are the failure point for particular inorganic zincs, we offer ceramic balls that will hold up somewhat better. The seats are already carbide and are extremely hard. Seats and balls should always be replaced together. The balls may look much worse, but the smallest wear on the seat will allow some leakage, and quickly start tearing into a new ball. 

Latest
Previous
Click here for Comments

1 comments:

avatar

I read this article; it is really informative one. Your way of writing and making things clear is very impressive. tuskbond.co.uk is the place where you get EPDM Contact Adhesive for sale online. Thanking you for such an informative article.